Terminal Town's Electrical Connector Solder Seals

Welcome To Terminal Town

We Are An Experimental Aircraft Builder Friendly Site Featuring Mil Spec Electrical Connectors and Related Product for Aviation, Marine and Everything Else That You Want To Use The Best Product On!

Terminal Town's Electrical Connector "How To" For Mounts

This page illustrates ways to secure and mount cables using cable ties.

CTM-HM Mount

This unit is for mounting and securing cables . It raises the mounted item up to reduce chafing and secures the item at the same time.

It meets MS3341-1-9. Dimensions: approx. 1" x 1" x .75".

[Image] [Image]

Mount vertically or horizontally with two #6 screws or pop rivets. The cable tie runs through unit parallel to the mounting surface or front to back. This allows you run cable through a bulk head or parallel to a mounting surface. This part will accept cable ties up to .190"wide .

[Image] [Image]

[Image]

[Image]

To purchase these mounts Click Here to go to the Cable Tie Page

Table of Contents

Privacy

Kits

STICKY BACK ADHESIVE MOUNTS
	Sticky Backs Mounts: The important thing to remember with sticky back mounts is to clean the surface to remove ALL dirt, grease, and loose materials. Peel off the protective backing and press into place. For more secure mounting use screws or pop rivets. The cable ties can be inserted from any of four directions. The sticky part is an acrylic adhesive foam backing and all of our CTMs come with screw holes for a #8 screws for an alternate mounting option. The mounts will accept an 18lb tie at .100" wide up to a 50lb tie at .187 wide.

STICKY BACK ADHESIVE MOUNTS

Sticky Backs Mounts:
The important thing to remember with sticky back mounts is to clean the surface to remove ALL dirt, grease, and loose materials. Peel off the protective backing and press into place. For more secure mounting use screws or pop rivets. The cable ties can be inserted from any of four directions. The sticky part is an acrylic adhesive foam backing and all of our CTMs come with screw holes for a #8 screws for an alternate mounting option. The mounts will accept an 18lb tie at .100" wide up to a 50lb tie at .187 wide.

PUSH MOUNTS
	This type of mount is called a Push Mount. It inserts into a 1/4" hole and provides a flat loop to insert a tie into. This can be used up to a max. panel thickness of .125" They will accept .100" wide 18lb ties up to .187" wide 50lb ties.
	The photos above on the left shows an uninstalled push mount and a installed unit. The photo on the upper right shows the tongue protruding through the panel. Photo on the left shows the position of the tie. This is a 50lb .187 wide 11" tie. Photo on right is the finished assembly. I used a blue high temp tie because it is easier to see in the photo.
MOUNT CABLE TIES
The photo on the right is a push mount tie. It works the same as the push mount saddle shown above. The tie is designed to either be cinched around the wire and then inserted into the mount hole or inserted and then position the wires, make your loop and draw the tie tight. It requires a 1/4" hole. They are available in lengths of 6" and 8" in a 50lb rating . All are available in black or natural. The 6" tie will wrap a 1-1/4" bundle. An 8" tie will wrap a 1-3/4" bundle. Minimum bundle size is 1/16".	Push Mount tie
This is a Stud Mount Tie. They are available in lengths of 6"at 30 lbs, 8" and 11" in a 50 lb rating. Also available is a stud mount with a 120 lb rating and a length of 15". All are available in black or natural. The 6" tie has a #8 stud hole size. The 8" and 11"has a #10 stud hole size and the 15" 120lb tie has a 1/4" stud hole size. The 6" tie will wrap a 1-1/4" bundle. An 8" tie will wrap a 1-3/4" bundle. An 11" tie will wrap a 3" bundle and a 15" tie will wrap a 4" bundle. Minimum bundle size is 1/16" on the 30lb and 50lb ties. It is 3/16" on the 120lb ties.	STUD MOUNT TIE

PUSH MOUNTS

This type of mount is called a Push Mount. It inserts into a 1/4" hole and provides a flat loop to insert a tie into. This can be used up to a max. panel thickness of .125"

They will accept .100" wide 18lb ties up to .187" wide 50lb ties.

Push mount finished assembly The photos above on the left shows an uninstalled push mount and a installed unit. The photo on the upper right shows the tongue protruding through the panel.

Photo on the left shows the position of the tie. This is a 50lb .187 wide 11" tie. Photo on right is the finished assembly. I used a blue high temp tie because it is easier to see in the photo.

MOUNT CABLE TIES

The photo on the right is a push mount tie. It works the same as the push mount saddle shown above. The tie is designed to either be cinched around the wire and then inserted into the mount hole or inserted and then position the wires, make your loop and draw the tie tight.

It requires a 1/4" hole. They are available in lengths of 6" and 8" in a 50lb rating . All are available in black or natural.

The 6" tie will wrap a 1-1/4" bundle. An 8" tie will wrap a 1-3/4" bundle. Minimum bundle size is 1/16".

Push Mount Tie

Push Mount tie

This is a Stud Mount Tie. They are available in lengths of 6"at 30 lbs, 8" and 11" in a 50 lb rating. Also available is a stud mount with a 120 lb rating and a length of 15". All are available in black or natural.

The 6" tie has a #8 stud hole size. The 8" and 11"has a #10 stud hole size and the 15" 120lb tie has a 1/4" stud hole size.

The 6" tie will wrap a 1-1/4" bundle. An 8" tie will wrap a 1-3/4" bundle. An 11" tie will wrap a 3" bundle and a 15" tie will wrap a 4" bundle. Minimum bundle size is 1/16" on the 30lb and 50lb ties. It is 3/16" on the 120lb ties.

[Image]

STUD MOUNT TIE

Terminal Town
9219 Co. Rd. 28 SW
Alexandria, MN. 56308

E Mail Us!

Terminal Town